- Input Impedance
- 10 kΩ (RCA), 20 kΩ (XLR)
- Weight (unpacked)
- 20 lb (9 kg)
Price $5,999
Includes GST
Voted Australia's #1 Hi-Fi Retailer, Sound+Image Awards 2023. Family owned since 2010.
Hear the Statement M1 before you decide
Book a private listening session in Belrose and ask for the Statement M1: we will confirm what we can set up for you. Or audition it at home.
Delivery and collection
Free standard shipping on orders of $300 or more within Australia, and $15 on smaller orders. Western Australia is quoted on request.
Pick up from our Belrose showroom: call ahead so we can have it ready.
Set-up and installation
Our team can deliver, install and set up your system, from speaker placement to a full cinema calibration. Ask us for a quote when you order.
Returns
Your rights under Australian Consumer Law always apply. Read our returns policy.
Anthem Statement M1
Specifications
- Power Output continuous, 20 Hz to 20 kHz, <0.1% THD+N
- Power Output continuous, 20 Hz to 20 kHz, <0.1% THD+N
- 8 Ω
- 1000 W
- 4 Ω
- 2000 W
- 3 Ω
- 2400 W
- 2 Ω
- >2000 W depending on line voltage regulation
- Frequency Response 20 Hz to 20 kHz
- Frequency Response 20 Hz to 20 kHz
- Open circuit
- +/- 0.1 dB
- 8 Ω
- +/- 0.1 dB
- 4 Ω
- +/- 0.1 dB
- 2 Ω
- +/- 0.2 dB
- Power Bandwidth 1000 W at 8 Ω
- 5 Hz to 45 kHz
With 120V AC supply the amplifier’s maximum output into impedances 4 Ω and lower, as well as its maximum duration, vary depending on line voltage regulation.
POWER REQUIREMENTS
Where mains voltage is 120V, one dedicated 15A circuit per amplifier is recommended depending on speaker. A 20A circuit is adequate for two amplifiers playing music where speaker impedance is 8 Ω. This product operates from a single phase AC power source that supplies between 108V and 264V at a frequency of 50 or 60 Hz.
In detail
About the Statement M1
State-of-the-Art Monaural Amplifier
The highest sound quality at all volume levels, flat frequency response into any load, and stable into the most difficult loads. The Statement M1 is a state-of-the-art monaural amplifier delivering 1,000 watts into 8 ohms and 2,000 watts into 4 ohms or less with THD remaining under 0.1% from 20 Hz to 20 kHz. Designed and engineered in our advanced research center in Ottawa, Canada, the M1 is manufactured in our Toronto facility.
More than just a slim, technologically advanced monaural design, the M1 demonstrates that Class D architecture isn't fundamentally flawed, it simply hasn't been implemented well in the past, mainly because it required such a heavy commitment to R&D. We’re fortunate to have the in-house resources to create such a groundbreaking product and one listen will reveal the truly extraordinary nature of this amplifier.
Cutting Edge Technology & Design
- Full resolution of all of the sonic subtleties and complexities in the input signal.
- Accurate reproduction of the full dynamic range of the signal.
- Output stage is never allowed to clip.
- No compression as output increases.
- Flat frequency response into any load, without having to resort to digital conversion or equalization to compensate.
- Stable into all loads including open circuit and short circuit.
- A low noise floor.
- Exceptional efficiency with low heat output.
- An amp so mechanically silent it will suit even the quietest listening room.
- A design that allows multiple units to be stacked with no danger of overheating.
- All of the above delivered at a price point that while not inexpensive, delivers virtually limitless dynamic fidelity.
By appointment
Hear it in a real room.
Specifications only tell half the story. Book a private listening session in our Belrose showroom, bring the music you know best, and ask for the Statement M1.
Voted Australia's #1 Hi-Fi Retailer, Sound+Image Awards 2023
- Family owned since 2010
- Talk to the people who will look after you.
- Listen in Belrose
- Private listening sessions, by appointment.
- Designed and installed
- Cinemas and listening rooms by our own team. (02) 8088 3088
Pairs with the Statement M1
Complete the system
- Sold outPre-owned
